dd wrt nvram
Hardware
NVRAM non-volatile RAM also called flash space is the place where the permanent settings are stored, This includes 1, 1,1, DD-WRT settings that you normally change using Web Interface 1,2, settings for user Startup Scripts You can run the following commands using Command Line: 1, Show the whole NVRAM content: 1, Show NVRAM content containing the pattern useful for quickly fi…
DD-WRT Forum :: View topic
1x Ubiquiti RouterStation Pro DD–WRT r23204 std 12/24/13 1x Asus RT-N16 SVN revision 20675 NEWD-2 K2,6 1x Linksys E4200 v3,0 r34777 mega 01/31/18 1x Buffalo WZR-HP-G300NH B0 B0 Gargoyle FW 1x Linksys WRT600N v1,1 Bricked 1x Linksys WRT54GL v1,1 DD–WRT 26446 1x Linksys WRT54GS v2,2 DD–WRT 26446 1x Linksys RVS4000 stock fw 3x D-Link DWL-7100AP …
DD-WRT Forum :: View topic | 14/06/2015 |
DD-WRT Forum :: View topic | 08/04/2013 |
DD-WRT Forum :: View topic | 29/10/2010 |
DD-WRT Forum :: View topic | 16/02/2010 |
Afficher plus de résultats
DD-WRT Forum :: View topic
Joined: 26 Aug 2011, Posts: 43, Posted: Tue Jan 24, 2012 4:32 Post subject: NVRAM – WRT610N, Hi, Just set up the latest build: DD–WRT v24-sp2 12/08/11 mega, SVN revision 17990M NEWD-2 K2,6 Eko On my wrt610n, I noticed on the status page, it says for …
DD-WRT Forum :: View topic
32k nvram help DD–WRT Forum Forum Index-> Broadcom SoC based Hardware: Goto page Previous 1, 2
Journalling Flash File System
Note that DD–WRT v24sp1 VPN builds have the JFFS feature removed, nvram set jffs_mounted=1 nvram set enable_jffs2=1 nvram set sys_enable_jffs2=1 nvram set clean_jffs2=1 nvram set sys_clean_jffs2=1 nvram commit reboot Note: Device might reboot/hang after cleaning which might take long; be patient, To unmount the JFFS: nvram set sys_enable_jffs2=0 nvram set sys_clean_jffs2=0 …
DD-WRT Router Guide
The DD-WRT default login details tend to match that of the router, but not only should you, but you will need to change this, That’s it you’re done with the DD-WRT firmware upgrade, If at any point you need to do a DD-WRT reset because you’ve made a mistake and the router is not responding, then do a 30-30-30 reset, Changing the Basic Settings
Useful Scripts
Should you run your dd–wrt unattended for years with traffmon enabled, you should use this script or you’ll run one day or the other into a nvram outage and its fancy effets as wireless changing ciphering mode etc You can adjust how long the log you’ll keep will be by changing the integer “100” in the eleventh line: the first loop searches the max say current data set date, in YYYYMM
Startup Scripts
Here are three ways to get dd–wrt to run them automatically, Another method to have scripts run at startup is to place them in the right folder, with the ,startup extension, Read more at Script_Execution Web Interface Method of Loading Scripts onto Router Prerequisites, Know how to use and access Web Interface; Know the sequence of commands you’d like to run every startup optional test
Installation
Choosing The Correct Firmware – Extremely Important
Serial Recovery
flash -offset=262144 -noheader 192,168,2,10:dd–wrt,v24_micro_generic,bin flash0 The command above tells the cfe to flash the firmware at a particular address location on the flash chip, instead of the location that the cfe thinks is the correct one, which obviously is not if it reports a bad boot block,
Switched Ports
DD–WRT r46604 and newer use swconfig on Broadcom, This page explains proper command line configuration of VLANs on the router’s internal switch internal and external ports, usually after using the GUI DD–WRT Setup -> Switch Config formerly VLANs tab, These instructions are necessary: Only for Broadcom-based routers,
Setup Wi-Fi VLANs with DD-WRT on RT-AC3200
download DD–WRT build for router search ‘RT-AC3200’ or your router model for the correct build remove the router from your network, perform factory reset using Hard reset method this will reset router’s IP address to 192,168,1,1 enter recovery mode, set your computer’s IPv4 address to something like 192,168,1,100 and connect to the
Linksys WAP54G
WARNING – DD–WRT was not originally intended to be loaded on a WAP unit, It was found that it will run but it is a tricky unit to load and have function correctly, Below are a compilation of methods/instructions to assist you with creating a DD–WRT-loaded WAP unit, LOAD AT YOUR OWN RISK, Hard reset does not work on this device, so it is not possible to clear NVRAM using the reset button, This
DD–WRT Forum :: View topic
Broadcom SoC based Hardware “Linksys WRT160N v1 update DD–WRT Forum Forum Index -> Broadcom SoC based Hardware View previous topic :: View next topic Author Message rfarinha DD–WRT Novice Joined: 15 Dec 2011 Posts: 19″
Pas de commentaire