The Evolution of IPSC Production Division Pistols

A Glock 34 is a sporting pistol, and did not make it on to the IPSC’s Production Division List because of a barrel length limitation, That other sport, the …

Glock Mod’s Allowed for IPSC Production

The Glock 34/35 are now allowed under USPSA production rules due to the amendment of the 5 inch barrel rule, Now production guns just have to fit the IPSC box which the 34 and 35 were designed to do, This is in the May/June issue of Front Sight in the Inside NROI article, page 9, Also, in the same issue Robin Taylor examines mods for Glocks and talks of using a Tungsten guiderod under the

Hello, I was reading the uspsa rule book, I was thinking about adding the following to my glock for production division: extended mag well extendedWinston, According to my understanding of the rules the mag well is not allowed in production since it is an external modification to the gun, If tHi Winston, I am terribly sorry to say this, but I think none of the mods are allowed for IPSC production, No external mods funnel, no replacemenI think Spook has the right idea in emailing for an official answer, but I disagree on a couple points, The Glock 34/35 are now allowed under USPSAWinston, no way on the mag well and mag release, The rod and striker are probably OK for USPSA Production, Realize the most important things on youThanks for the info guys! Do you think it’s legal to have bomar’s installed this way? it requires milling of the slide: http://www,geocities,com/daHey guys, Another quick question, I was told that you cannot use holsters like a cr speed holster for the glock in production, What holsters and maWinston, I recommend holsters and mag pouches from Blade-Tech www,blade-tech,com, They are made of Kydex, have tension screws so you can set themTry the holster from KYTAC—– http://members,aol,com/KyTac You can get these the easiest from SKD— http://www,skdtac,com/ Once I tried these IAny internal work is allowed in production, The key here is weight, the gun cannot be over 2oz from factory condition, Striker= OK Recoil Rod= OK M

PRODUCTION DIVISION LIST

Fichier PDF

Also approved: variants with original Glock barrels which are longer than standard e,g, 17A, 17DK, as well as variants with “Tactical”, “Mariner” or similar OFM engravings on the slide, provided the barrel length does not exceed 127mm, and provided all other aspects of these variants fully comply with all other Production Division rules, Also approved: Gen 4 and SF versions of above models

Production Division – IPSC Action Air Mongolia

Also approved: variants with original Glock barrels which are longer than standard e,g, 17A, 17DK, as well as variants with “Tactical”, “Mariner” or similar OFM engravings on the slide, provided the barrel length does not exceed 127mm, and provided all other aspects of these variants fully comply with all other Production Division rules,Also approved: Gen 4 and SF or FS versions of

Glock 17 for Production?

FWIW: Bob Vogel placed first in the 2011 IPSC World Shoot Production division using a G-17, Under the old s#!tty trigger rules That doesn’t prove anything, except for the fact that Vogel won, In fact, using a glock to compete among Tanfoglio / CZ would have been a really bad idea,

If you train with it and can master your gripwith any gun for that matter it’s absolutely a viable option, Compete with it for now and eventuallyShoot whatcha got! Don’t worry about the pistol and go shoot a match, Get some under your belt and then figure out what you need, gear wise, from eGlocks hold their own in Production division just fine,Shoot it until you notice you’re losing a lot by using it you will notice at a certain point Don’t take too much time to switch to something bettTotally fine choice, And plenty of aftermarket support and probably the simplest gun for DIY efforts, Possible negatives- Mags can be sticky/slow tMaybe after january 2019 at least for IPSC it could reach a competitive level, but what is lost in recoil can’t be gained in anything else, The tI disagree with you completely,FWIW: Bob Vogel placed first in the 2011 IPSC World Shoot Production division using a G-17, Under the old s#!tty trigger rules ?That doesn’t prove anything, except for the fact that Vogel won, In fact, using a glock to compete among Tanfoglio / CZ would have been a really baIf there was no difference, everybody would pick the cheapest gun working, not the ones that cost more, It can’t be that 95% of shooters are so stu

Afficher plus de résultats

IPSC :: Rules

Handgun Divisions

New Handgun Division: IPSC Production Optics -The Firearm Blog

But Production Optics is NOT Open, There are shots I would do in Open without hesitation that I would not even think of with my Glock, regardless of which sight I use, You can find the latest IPSC Production Optics Division on trial regulations below, A recent addition to the Optics Division is the Walther PPQ Q4Tac,

IPSC

Participando da competição de IPSC na divisão PRODUCTION OPTICS com a GLOCK 17 M,O,S e Red Dot Vortex Venom 6 MOA,Ainda tenho muito o que melhorar ?As panes

, Liste des armes de la nouvelle division IPSC Production

Liste des armes de la nouvelle division IPSC Production Optique, 23 octobre 2017, IPSC, Voici la règlementation annoncés: Techniquement; l’arme qui doit être incluse dans la liste des armes acceptées en production pourra être munie d’une mire optique électronique étant installée dans la fente de retenue de la mire d’origine, le « machinage » de la slide est interdit, Une plaque

Why I shoot Glocks in IPSC/IDPA

There tend to be more glocks in production division where 1911 style guns and other s/a only guns are prohibited, In limited division, where I shot, nearly all the shooters had ,40 cal, custom 1911s that hold 20 +1 rds, I was at a distinct disadvantage since I was using stock Glock mags in my 35 that hold 15 and I can only get 14 in them, I don’t see too many Sigs or other styles of guns in

IPSC

IPSC

Welche Pistole für IPSC und Co,

Das beste wäre es bei der Glock zu bleiben weil diese für den Einstieg ins IPSC Production auch gut geeignet ist, Das Geld würde ich dann in Munition und Trainerstunden investieren, Das bringt dir mehr als eine neue Waffe, DVC, Nach oben, doc steel MUSCLEGUNNER Beiträge: 9758 Registriert: So 9, Mai 2010, 11:02, Re: Welche Pistole für IPSC und Co, Beitrag von doc steel » So 5, Mär 2017

Glock 17 GEN 5 Production Division

Glock 17 GEN 5 Production Division, Went straight to a competition without even testing the gun,Finished 3rd over-all out of 50+ shooters,