Series 90-97

Series 90–97 meets AISC requirements of Class B surface with a mean slip coefficient no less than 0,50 and a tension creep not in excess of ,005 inches ,13mm, Tneme-Zinc uses a zinc pigment which meets the requirements of ASTM D 520 Type III and contains less than ,002% lead, This level qualifies it to be classed as “non-lead” less than 0

FICHE TECHNIQUE DU PRODUIT: TNEME-ZINC

Fichier PDF

TNEME-ZINC , SÉRIE 90–97 GARANTIE ET LIMITATION DE RESPONSABILITÉ DU VENDEUR : Tnemec Company, Inc, garantit uniquement que ses revêtements attestés par la présente répondent aux normes de composition de Tnemec Company, Inc, LA PRÉSENTE GARANTIE DÉCRITE DANS LE PARAGRAPHE CI-DESSUS REMPLACE TOUTE AUTRE GARANTIE EXPRESSE OU IMPLICITE, Y …

PRODUCT DATA SHEET: TNEME-ZINC

Fichier PDF

TNEME-ZINC , SERIES 90–97 WARRANTY & LIMITATION OF SELLER’S LIABILITY: Tnemec Company, Inc, warrants only that its coatings represented herein meet the formulation standards of Tnemec Company, Inc, THE WARRANTY DESCRIBED IN THE ABOVE PARAGRAPH SHALL BE IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED …

FICHE TECHNIQUE DU PRODUIT: TNEME-ZINC

Fichier PDF

COULEURS 90–97 gris rougeâtre PIGMENT DE ZINC 83 % en poids d’extrait en feuil sec QUALIFICATIONS SPÉCIALES La Série H90-97 satisfait aux exigences AISC quant aux surfaces de classe B avec un coefficient de friction moyen pas inférieur à 0,50 et un glissement en traction pas supérieur à 0,005 pouce 0,13 mm, Tneme-Zinc contient une poussière de zinc qui répond aux …

Series 90-97

Contact your Tnemec representative, Note: Series 90–97 must be exterior exposed for three days prior to topcoating with Series 1028 or 1029, Note: Series 90–97 must be exterior exposed for one day prior to topcoating with Series 27WB, Volume Solids: 63,0 ± 2,0% mixed Recommended DFT: 2,5 to 3,5 mils 65 to 90 microns per coat, Curing Time

PRODUCT DATA SHEET: TNEME-ZINC

Fichier PDF

COLORS 90–97 Reddish-gray ZINC PIGMENT 83% by weight in dried film SPECIAL QUALIFICATIONS Series H90-97 meets AISC requirements of Class B surface with a mean slip coefficient no less than 0,50 and a tension creep not in excess of ,005 inches ,13mm, Tneme-Zinc uses a zinc pigment which meets the requirements of ASTM D 520 Type III and contains less than ,002% lead, This level qualifies it to

Series 90G-1K97

90G-1K97 Tneme-Zinc uses a pigment which meets the requirements of ASTM D 520 Type III and contains less than ,002% lead, This level qualifies it to be classed as “non-lead” less than 0,009% lead by weight as defined in 16 CFR Part 1303 of the Consumer Product Safety Commission regulations, Conforms to SSPC Paint 20, Type II,

PRODUCT DATA SHEET: TNEME-ZINC

Fichier PDF

TNEME-ZINC , 90–97 & H90-97 WARRANTY & LIMITATION OF SELLER’S LIABILITY: Tnemec Company, Inc, warrants only that its coatings represented herein meet the formulation standards of Tnemec Company, Inc, THE WARRANTY DESCRIBED IN THE ABOVE PARAGRAPH SHALL BE IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED …

High Performance Protective Coating Products

RGB: 119,114,110, 1 results found for ” Series 90–97 , Tneme-Zinc “, 25 per page 50 per page View All,

Search Results

Series 90–97 , Tneme-Zinc, Uses Primer and/or Block Fillers, For Steel, Generic Description Aromatic Urethane, Zinc-Rich, An advanced technology, two-component, moisture-cured, zinc-rich primer providing extraordinary performance, It’s user friendly and rapid curing so chemical- and corrosion-resistant topcoats can be applied the “same-day,”,

High Performance Protective Coating Products

Series 90–97 , Tneme-Zinc, Uses Primer and/or Block Fillers; For Steel; Generic Description Aromatic Urethane, Zinc-Rich; An advanced technology, two-component, moisture-cured, zinc-rich primer providing extraordinary performance, It’s user friendly and rapid curing so chemical- and corrosion-resistant topcoats can be applied the “same-day,” Also used for field touch-up of inorganic zinc

Tnemec Zinc-90-97&H90-97 by Tnemec is comparable to

Barrier 77 9 Litres may not be an exact match for Tnemec Zinc-90-97&H90-97 by Tnemec but we have given the closest match we can, Barrier 77 9 Litres should do the same job and have similar properties but you should always read the technical data sheets for both Barrier 77 9 Litres and Tnemec Zinc-90-97&H90-97 to be sure, Please see any notes to see any major differences and call us on 01285

Series 90-97 Datasheet — Tnemec Company, Inc, — Tneme

TNEME-ZINC — SERIES 90–97 Tnemec Company, Inc, List your products or services on Engineering360, Contact Information 6800 Corporate Drive Kansas City, MO 64120 USA Phone: 800 TNEMEC-1 816 483-3400, Fax: 816 483-3969 Business Type: Manufacturer, Supplier Profile, Supplier Website Tnemec Company, Inc, List your products or services on Engineering360, Contact …

Tnemec-zinc

Discussion Starter, #17, Jan 19, 2017, CApainter said: The maximum range offered in the TDS for ambient temperature cure times, is 4 hour recoat at 75 degrees F, that’s without the excelerator I believe, google tnemec 90–97 for the product TDS, And as …